Hydroman® Fishfarm Pond Electric Dredge Pump for Dam Dredging Description:
Hydroman® Fishfarm Pond Electric Dredge Pump for Dam Dredging is equipped with a agitator or stirring on a concentric shaft with the slurry pump impeller, so the Submersible Mining Tailings Pump for Heavy Slurry can be also called submersible agitator slurry pump or submersible slurry mud pump with agitator. The agitator on the bottow of submersible tailing mud pump can directly contact the mud, sewage sludge, slush, muck and sand layer, then the sediment can be stirred into turbulence, so that sumbmersible sand suction pump can be achieved heavy slurry and high concentration transport and the slurry absorbing effect is excellent.
Hydroman® Fishfarm Pond Electric Dredge Pump for Dam Dredging Operating Conditions:
▪ Power Source: 380V/460V, 50/60Hz, 3 Phase.
▪ Max. Temperature of Liquid: 80℃
▪ Max. Concentration of Solids: should not exceed 70%, Max. specific gravity not more than 1.50
▪ Max. Submersed Depth: 80m (the motor must be submersed in liquid)
▪ The best installation is vertical, max. incline should not exceed 10°
Note:If operating condition is different than above, please specify with order
Hydroman® Fishfarm Pond Electric Dredge Pump for Dam Dredging Constructional Drawing:
Hydroman® Fishfarm Pond Electric Dredge Pump for Dam Dredging Operating Features:
▪ Submersible Motor is protected by double mechanical seal and lip seals to prevent the entry of water and other impurities into motor.
▪ An agitator fitted on the end of main impeller mixes the solid and liquid, allowing the pump to lift the liquid and solid together. The wet parts of the pump are constructed of a hard chrome alloy material (65 HRC) designed to prolong service life.
▪ Motor and pump are submersed in liquid, saving installation space, protecting the equipment, allowing ease of maintenance, and greatly reducing operating noise.
▪ The motor has been designed to include several internal protection measures.
Hydroman® Fishfarm Pond Electric Dredge Pump for Dam Dredging Application:
▪ Mine Pits Dewatering
Pit-installed pumps on pontoons or barges commonly use submersible mine dewatering pump. For booster stations submersible pumps connected in series, single-stage end-suction or multistage pumps can be used. These solutions can be provided in containerized units for ease of installation and transportation.
▪ Underground Mine Dewatering
Submersible underground mine pumps are used to remove water from mine faces nd stopes. Water is transported in stages to collection stations where larger pumps are located along the drift and ramp. Normally smaller submersible drainagepumps are used at the mine faces.
▪ Shaft bottom drainage
Mine water from all parts of the mine is collected by submersible dewatering mud pump in the shaft bottom sump and then transported to the main drainage pump station. The high-performance submersible electric slurry sludge pumps fulfill the requirements, meeting the demands for both high head and high volume
▪ Tailings Ponds and Mineral Recovery
The scarcity and cost of water means that wastewater treatment and recycling for reuse are important processes within mines. Water is reclaimed from tailings ponds, lagoons and the downstream of minerals processing by vertical sump slurry pump, horizontal sludge pump and submersible sand pumps.
▪ Water treatment
Minerals processing requires process water feed at various stages. The quality of the water is highly important and therefore some level of treatment is needed before it enters the process. A combination of submersible water treatment sludge pumps, horizontal process pumps and vertical mineral processing pumps are commonly used in the feed to the proces.
▪ Mine sites
Other common applications for pumps at mine sites are tire washing plants, washdown of plant and machinery, and dust suppression. These may be fed by submersible slurry pump.
